ServicesPool Repair
Pool Repair in Chandler
When your pump hums but won't start, the filter gauge climbs too fast or the heater clicks and quits, we find the part that failed and replace that part. The technician who diagnoses your equipment is the same one who comes back to finish the repair.
Repair That Starts With the Cause
Most pool equipment problems trace back to a handful of parts: a run capacitor, worn motor bearings, a cracked shaft seal, a torn spider gasket inside a multiport valve, a fouled salt cell or a heater pressure switch that never closes. Replacing the whole unit is rarely the first answer. We test the components, tell you which one is bad and explain why it failed.
Our crew is small on purpose. The person who opens your equipment pad and reads the symptoms is the person who orders the part and installs it. You don't have to repeat the story to someone new, and nothing gets lost between a sales visit and a service visit.
If the honest answer is that a 15-year-old pump isn't worth another motor, we'll say so and walk you through options on our Equipment Installation page instead.
What Our Pool Repair Covers
- 01
Pumps and motors
We replace capacitors, bearings, shaft seals, impellers and diffusers, and we clear impellers packed with leaves or debris. Long summer run times in Chandler wear motor bearings faster, so we check for heat damage and grinding while we're there.
- 02
Filters and valves
Cracked filter tanks, broken laterals in sand filters, torn DE grids, failed tank clamps and worn spider gaskets in multiport valves. A bad gasket sends water past the filter and straight back to the pool, which is why the water stays cloudy no matter how long you run it.
- 03
Heaters and heat pumps
Igniters, flame sensors, pressure switches, high-limit switches and control boards. Many heater faults are actually low water flow from a dirty filter, so we check flow before blaming the heater.
- 04
Salt systems and automation
Salt cells that read low, flow switches that stay open, timers and automation panels that stopped running schedules. We clean or replace the cell and confirm the controller is reading true salt levels.
- 05
Plumbing and fittings
Cracked PVC at the pad, sun-brittle unions, stripped drain plugs, broken skimmer weir doors and loose return fittings. Above-ground pipe at the equipment pad takes direct sun all year, and that UV exposure is the usual reason it cracks.
Questions about Pool Repair?
Call(480) 582-9044Signs Your Equipment Needs Repair
Pump hums but won't spin
A humming motor that doesn't start usually points to a failed capacitor or seized bearings. Turn it off. Leaving it humming overheats the windings and can turn a small part into a new motor.
Grinding or screeching noise
That sound is almost always motor bearings. Caught early, bearings can often be replaced; ignored, they take the motor with them.
Water under the pump
Water dripping from between the pump and motor means the shaft seal has worn out. Water reaching the motor will corrode its bearings, so this one is worth fixing soon.
Filter pressure that won't settle
Pressure that jumps right after cleaning can mean a collapsed grid or cartridge. Pressure that stays unusually low often points to a suction-side problem like an air leak at the pump lid O-ring.
Air bubbles in the returns
Steady bubbles from the return jets mean the pump is drawing air somewhere on the suction side, usually a dry lid O-ring, a cracked union or a low water level.
Breaker trips when equipment starts
A tripping breaker can be a shorted motor, a failing heater component or a wiring fault. We isolate which piece is drawing the problem before replacing anything.
How a Repair Visit Works
- 1
Talk it through by phone
You describe what the equipment is doing, any error codes and the brand if you know it. We set a time to look at it and you get your free quote by phone once we know the cause.
- 2
Diagnose at the pad
Your technician tests voltage, checks the capacitor, reads filter pressure, inspects seals and gaskets and watches the system run. We show you the failed part and explain what caused it.
- 3
Quote the actual repair
You get a line-by-line quote covering parts and labor before any work starts. If a repair costs close to what replacement would, we tell you that plainly.
- 4
Same technician finishes the job
The person who diagnosed it installs the part, primes the system, checks for drips and air, and confirms pressure and flow are back where they belong. We clean up the pad and haul off the old parts.
What Affects the Cost of Pool Repair
Repair pricing depends on which part failed and how hard it is to reach. We quote after diagnosing, so you pay for the problem you actually have, not a guess. Here is what moves the number.
- The failed part
- A capacitor or O-ring is a small part with short labor. A motor, heat exchanger or control board costs more in parts and time.
- Brand and part availability
- Common pumps and filters use parts that are easy to source. Older or discontinued models may need adapters or a different approach.
- Plumbing changes
- If a repair requires cutting and re-gluing PVC, for example to replace a pump with different port heights, labor goes up.
- Age and condition of the system
- Brittle pipe, corroded unions or a motor near the end of its life can turn one repair into two. We point these out before work begins so nothing surprises you.
Pool Repair Questions
Should I repair my pump or replace it?
It depends on what failed and how old the pump is. A capacitor, seal or bearing set on a pump in good shape is usually worth fixing. If the motor is burned out on an older single-speed pump, replacing it with a variable-speed model often makes more sense, and we'll explain the tradeoff.
Can I keep running the pump until you get here?
If it hums without spinning, smells hot or trips the breaker, shut it off. Running it can damage the motor windings. A pump with a small drip at the seal can usually run briefly, but get it looked at soon.
Do you work on salt systems and heaters, or only pumps?
We repair pumps, filters, valves, heaters, heat pumps, salt chlorine generators, timers and automation controls. If your issue is in the water itself, such as algae, that's covered by our Green to Clean Recovery service.
Will the same person come back to finish the repair?
Yes. We're a small crew, and the technician who diagnoses your equipment is the one who returns with the part. That keeps the details straight and saves you from explaining the problem twice.
Do you serve areas outside Chandler?
We also handle repairs in Gilbert, Mesa, Tempe, Sun Lakes, Queen Creek, Guadalupe and Sacaton. Mention your town when you call and we'll set up a visit.
Get Your Equipment Running Right Again
Tell us what your pump, filter or heater is doing and we'll set up a diagnosis. You'll know the cause and the cost before any work starts.